Amano MRX-35 Manuale delle Operazioni

MRX-35 Electronic Calculating Time Recorder Setup and Operations Manual

1-6 MRX-35 The LCD Display The LCD display on the front panel displays the current date, time and day of the week, along with programming informatio

MRX-35 1-7 Normal Operation During normal operation, the time and date are displayed. Programming Mode In the programming mode, the display will

1-8 MRX-35 Other Components • (3) Basic Programming Cards • (3) Advanced Programming Cards

MRX-35 2-1 Chapter 2: Getting Started Placement/Location When choosing a mounting location for your MRX-35, you should consider the following: • Th

2-2 MRX-35 Wall Mounting 1. Disconnect the power cord from the power source, if applicable. 2. Set the MRX-35 (display side down) on a flat surfa

MRX-35 2-3 6. Using the back plate as a template, approximate the final location of the MRX-35, and mark the location of the teardrop-mounting hole

2-4 MRX-35 Power Connection Plug the power cord into a suitable grounded outlet. When the AC power is properly connected, the MRX-35 will cycle

MRX-35 2-5 The Time Card The MRX-35 is designed for use with the following time card: Item Function/Description Side Indicator Indicates the side

2-6 MRX-35 Item Function/Description Daily Net This column displays the total amount of hours for a given pair of punches or a day. This total m

MRX-35 2-7 How to Insert a Time Card 1. Make sure that there is power to the MRX-35. 2. Verify that you are using the correct side of the time card

Proprietary Notice This document contains proprietary information and such information may not be reproduced in whole or part without the written pe

2-8 MRX-35 This page intentionally left blank.

MRX-35 3-1 Chapter 3: Programming Introduction The MRX-35 must be programmed and configured before use. Basic Programming consists of time, date, im

3-2 MRX-35 Basic Programming Time Settings To set the time (Hours and Minutes), perform the following: 1. Insert MRX Basic Programming Card #1 Sid

MRX-35 3-3 3. Press the Next button to enter the values selected. The card and the display will advance to the Pay Period Type position. You may als

3-4 MRX-35 2. Select the Pay Period Type by pressing the corresponding button indicated by the programming card. The codes for the Pay Period Type a

MRX-35 3-5 Daylight Saving Time The MRX-35 is shipped from the factory with the Daylight Saving Time (DST) feature enabled. However, it can be disab

3-6 MRX-35 3. Press the Next button to enter the values selected. The card will advance to the Daylight Saving Time End Date position. You may also

MRX-35 3-7 Day Change Time The Day Change Time is the time of day that a normal business day ends. It advances the virtual time used for time calcul

3-8 MRX-35 Day Change Override The Day Change Override Time determines if an employee’s OUT punch will correspond to the next or previous day when

MRX-35 3-9 Example 3: The default value of the Day Change Override is set to 12:59 (12 hours and 59 minutes from the IN punch). If you wish to chan

MRX-35 i Table of Contents GUIDELINES FOR SAFE OPERATION….. ... 1-1Chapter 1: Overview ...

3-10 MRX-35 Time Rounding Time Rounding is used to simplify the calculation of accumulated hours. When an IN/OUT punch equals or is greater then th

MRX-35 3-11 3. Press the Next button to enter your selection. The card and the display will advance to the Rounding Point position. You may also pres

3-12 MRX-35 Automatic Break Up to two Automatic Breaks can be programmed in the MRX-35. Each break deduction is limited to a maximum of four hours.

MRX-35 3-13 At 13:00 hours, Auto Break #2 will begin and the employee will punch out. At 13:45 hours, the employee will punch back in. At this time,

3-14 MRX-35 6. Press the buttons indicated by the programming card for the time (hours and minutes) required to work to qualify for the break ded

MRX-35 3-15 Daily and Weekly Overtime Overtime can be calculated on a daily or weekly basis; two levels of overtime can be set for each one. For ove

3-16 MRX-35 To set the Daily OT threshold levels, perform the following: 1. Insert MRX Basic Programming Card #2 Side B and position it to the Dail

MRX-35 3-17 To set the Weekly OT threshold levels, perform the following: 1. Insert MRX Basic Programming Card #2 Side B and position it to the Week

3-18 MRX-35 Imprint and Display Mode The MRX-35 allows you to select the printing format of the hours on the time card. The hours setting also appl

MRX-35 3-19 Date Print Mode In addition to hours and minutes, you can also choose whether to print the day or date on the time card. By default, the

ii MRX-35 Revision Zones ... 3-35Chapter 4: Maintenance and Troubleshooting ...

3-20 MRX-35 Fixed Break A single Fixed Break can be programmed. The break is defined by the Start and End Times entered. The amount of time for the

MRX-35 3-21 4. Press the Next button to enter the values selected. The card and the display will advance to the Overtime Type position. You may also

3-22 MRX-35 2. Press the button for the desired Overtime Type as indicated by the programming card. A code will appear in the display. The codes ar

MRX-35 3-23 Data Initialization This selection is used to print out programmed settings or reset your MRX-35 programmed settings to their default va

3-24 MRX-35 No. Programming Item Default 03 Pay Period 0 04 Pay Ending Day 7 05 Daylight Saving Time 1 06 Daylight Saving Time Begin/ End

MRX-35 3-25 No. Programming Item Default 31 Exception 1 Punch Type 0 32 Exception 1 Start/End Times **:**/**:** 33 Exception 2 Punch Type 0

3-26 MRX-35 Advanced Programming Exception Zones An Exception Zone is used to print a diamond symbol  next to the punch time on the time card duri

MRX-35 3-27 5. Press the buttons indicated by the programming card for the Start and End times of the Exception. 6. Press the Next button to ente

3-28 MRX-35 3. Press the Next button to enter your selection. The card and the display will advance to the Exception 2, Start and End Time position.

MRX-35 3-29 2. Select the Punch Type for Exception 3 from the choices indicated by the programming card and the code in the display. They are: Code

MRX-35 1-1 GUIDELINES FOR SAFE OPERATION….. To ensure safe operation, please carefully read the following warnings and cautions prior to using the

3-30 MRX-35 6. Press the Next button to enter the values selected. The card and the display will advance to the Exception 4, Punch Type position. Yo

MRX-35 3-31 3. Press the Next button to enter your selection. The card and the display will advance to the Exception 4, Start and End Time position.

3-32 MRX-35 2. Select the Punch Type for Exception 5 from the choices indicated by the programming card and the code in the display. They are: Cod

MRX-35 3-33 6. Press the Next button to enter the values selected. The card and the display will advance to the Exception 6, Punch Type position. You

3-34 MRX-35 3. Press the Next button to enter your selection. The card and the display will advance to the Exception 6, Start and End Time position.

MRX-35 3-35 Revision Zones A Revision Zone is a window of time in which the employee may punch in or out (not both), but the MRX-35 will not begin o

3-36 MRX-35 To create Revision Zone 1, perform the following: 1. Insert MRX Advanced Programming Card #5 Side A. The card will stop at the Revision

MRX-35 3-37 6. Press the Next button to enter the values selected. The card and the display will advance to the Revision 2, Punch Type position. You

3-38 MRX-35 3. Press the Next button to enter your selection. The card and the display will advance to the Revision 2, Start and End Time position.

MRX-35 3-39 If None is selected (Code 0), the card and display will advance to the Revision 4, Punch Type position. 3. Press the Next button to ente

1-2 MRX-35 Do not place the unit near kitchen counter or humidifier. Oil, smoke, or steam generating from them may cause fire or shock hazards.

3-40 MRX-35 To create Revision Zone 4, perform the following: 1. If you have not already done so, insert MRX Advanced Programming Card #5 Side B, a

MRX-35 3-41 5. Press the buttons indicated by the programming card for the Start and End times (hours and minutes) of the Revision. 6. Press the

3-42 MRX-35 4. Press the buttons indicated by the programming card for the Start and End times (hours and minutes) of the Revision. 5. Press th

MRX-35 3-43 To create Revision Zone 6, perform the following: 1. Select the Punch Type for Revision 6 from the choices indicated by the programming

3-44 MRX-35 This page intentionally left blank.

MRX-35 4-1 Chapter 4: Maintenance and Troubleshooting Cleaning (Exterior) ！ WARNING!: • Unplug the unit before attempting to clean it. • Do no

4-2 MRX-35 Ribbon Replacement The Ribbon Cartridge (P/N CE-319250) should be replaced when the imprint becomes too light. To replace the ribbon:

MRX-35 4-3 6. Press the ribbon down until it clicks into place. Turn the knob clockwise to remove any slack in the ribbon. 7. Put the Top Co

4-4 MRX-35 Fuse Replacement ！ WARNING!: Disconnect the power cord from the power source before attempting to change the fuse. If the fuse (P/N EFS-

MRX-35 4-5 7. Locate the fuse. Replace the desired fuse only with one of the same type and rating. 8. With the front cover on a flat surface and

MRX-35 1-3 Chapter 1: Overview Operation Summary The MRX-35 is an advanced electronic time recorder that calculates daily and weekly employee hou

4-6 MRX-35 Error Codes The table below lists the possible Error Codes that may appear in the display and their causes. Figure 4-1 Error Code Mess

MRX-35 4-7 Error Code Description Possible Cause and Solution E-96 CPU Error Internal error. Contact your local Amano service dealer or representa

4-8 MRX-35 Error Code Programming Card Description P-31 Advanced Programming Card #4 Side A Exception 1, Punch Type P-32 Exception 1, Start/End T

MRX-35 4-9 Default Programming Values Basic Programming Item Initial Value Input Data Time Setting 12:00 Hour/Minute (∀) Date Setting 2002/01

4-10 MRX-35 Advanced Programming Item Initial Value Input Data Rounding Unit 15 1/6/15/0 Rounding Point 8 1/4/8/0 Daily OT1 : 00:00 – 23:5

Chapter 5: Specifications Power Requirements: AC 110-120V±10% 50/60Hz Power Consumption: 4W, Idle. 13W or less, Printing Dimensions: 233 mm H X 17

ARX-100900-2 Copyright © 2012 Amano Cincinnati, Inc. 02/12 This page intentionally left blank.

www.amano.com/time

1-4 MRX-35 User enrollments (ID numbers) are not required for the MRX-35. Hours are stored for each user in the MRX-35 under a special user number t

MRX-35 1-5 External View Button Functions In the normal mode, all buttons are disabled. In the programming mode, the buttons have the following fun